victorian - Doing It-Projects with CSBergman

How to Make Realistic Stone Bricks on a Pepperwood Farm Dollhouse

This is my Pepperwood Farm Dollhouse from previous posts, with an updated exterior!

I have debated for a long time on the exterior of my Pepperwood Farm dollhouse–it had light blue siding on it from a previous owner, and the siding wasn’t done very well, or maybe it shrank over time, and had a lot of gaps. I have wanted a brick dollhouse for a while, and when my husband said ‘no more dollhouses,’ (which is reasonable, I guess, as I have 13 in our small house), I decided to update my Pepperwood with some bricks!

It all came about as I wandered the aisles of our local Menards hardware store and stumbled on a pile of stone-like backsplash on clearance.

The backsplash. It is very rough and stone-like.

The backsplash came as strips of stone-like material, all held together with a big sticker on the back. I needed to separate these strips and then cut them into bricks to attach to my dollhouse.

Step 1: Separating the strips.

I used my handy-dandy box cutter and an old piece of wood as a cutting board, and scored the underlying sticker between the strips of bricks.

Individual strips.

Step 2: Cutting the strips into bricks.

I used my miter shears to carefully cut the stone pieces into bricks. This was very difficult work, but worth it in the end. I eventually discovered that it was to my benefit to point the shears inside a box to catch the bricks, to prevent them flying all over the place after being cut.

Using a box to catch the bricks.

Step 4: Placing the bricks.

Placing the first bricks. These have an adhesive back, so I just peeled the paper backing and stuck them in place! The grout mortar I will add afterword will help seal them to the house better.

More bricks! I used the copper strips that were in the backsplash to make ‘supports’ for the windows. I left space above the windows to make fancy brickwork later.

And more bricks.

Most of the bricks placed.

Brick arches above windows. I wanted it to be somewhat reminiscent of the brick farm houses common in my area.

Step 5: mortaring between the bricks.

This step was probably the hardest, most time-consuming dollhouse project I have yet accomplished. I can not begin to add up all of the many hours I spent performing this task.

I ended up using un-sanded tile grout, mixing it into a thin paste, filling a tiny squeeze bottle, and squeezing it between the bricks. I had to used a thick piece of wire to push the grout around in between the bricks to fill any gaps.

This is the squeeze bottle I used. It came with many fine tips but this one worked best. The grout ‘mortar’ had to be mixed to just the right consistency to be easily squeezed from the bottle, but not thin enough that it runs when you squeeze it in place.

Squeezing mortar between the bricks. The white mess in the lower left was from when I first started, trying to get the hang of it. I eventually touched the bricks up with paint there.

Using a thick wire ‘rod’ to push the mortar around to fill in gaps.

A little more progress.

More progress. Many hours of work. That is a cast iron door stopper holding the back of the dollhouse closed, so curious cats don’t sneak in and redecorate.

Almost done

Step 6: a stone foundation. I wanted to add this before aging the bricks, so i could age the foundation at the same time.

I wanted to make the bottom foundation more of a natural stone instead of bricks, so I thought I would try the egg carton/modpodge method. You start with a cardboard egg carton and break it into pieces (for this project I only needed one carton).

Egg carton

Then I used Modpodge and a cheap bristle paintbrush from DollarTree (I think it was a stencil brush).

I basically just pasted the cardboard pieces all over the base of the dollhouse so it looked like stones. I built them up in layers to add depth.

Doesn’t look like much while it is wet, but when it is dry…

So satisfying.

I eventually decided to keep the ‘stone’ on the base as-is, without painting it, so I went back through and added a few more pieces to cover up any writing left exposed on the cardboard.

Step 7: Aging.

I didn’t want the stark white grout between the bricks to stay that color, as it just isn’t very natural looking, so I knew right away that I would age it with some watered down paints.

Watered down acrylic paints and my good old bristle stencil brush. The bristle brush is good for digging into crevices with your weathering paints.

I ended up using brown, a little green, and a tiny bit of black, making various washes over different areas of the house to make it look weathered. Just like any real house, the weathering will not be consistent through the entire finish, as variations in architecture, sun exposure, potential leaks, water runoff, etc will create different effects. I just varied it enough to make it interesting.

Patting off excess paint with a paper towel.

Working paint into those cracks and crevices.

In a brighter light.

This house project took so MANY hours to complete, and my hands were so sore from squeezing that little squeeze bottle, but I am so pleased with how it all turned out. My next plans for this include making gutters to cover some of the white trim on the corners (I should have removed the trim before putting on the bricks, but hadn’t thought about it until it was too late). Also I have started remodeling the bathroom. Stay tuned for more!

How to Make Working Dollhouse Windows from Scratch

For my new-ish 1920’s style house, I had a hard time finding room for it and ended up keeping it on the floor, under a table that has another house on it. Unfortunately, my darling kitties have discovered that it has no plastic in the windows, and they can slip their paws in and play with my mess. (I have furniture inside, but the inside was basically stripped before I got the house–no trims, doors, flooring, even the wallpaper was ripped off the walls.) Anyway, I made it a priority to get windows on it.

At first I was just going to slap clear plastic into a frame and call it done. Then, after studying the working windows in my Pepperwood farm house, I decided that I might be able to make some working windows.

For this project, I collected clear plastic from different food containers to use as the ‘glass.’ It is clear, it is cheap, it is sturdy enough, and it is easily available. I have my own little collection that I have been building over the past couple of years for projects such as this, mostly the tops off mini doughnut lids from Walmart. Anyway, I also used Hardwood Outside Corner Trim from Menards. This trim has two equal sides that form a right angle to each other.

Hardwood Outside Corner Trim from Menards, with my handy dandy miter shears.

I also used my miter shears, wooden coffee stirrers, and wood glue.

First, I used the miter shears to cut the corner trim at the proper angles and sizes to make a frame inside the window. I glued the pieces together, so it is an inner frame for my window hole. When you hold it up, it will look like a picture frame where the outside of the frame is nice and flat, while the inside has a raised ridge that will hold the window workings.

Example of a measured and cut piece to line the inside of the window hole.

I placed the new inner window frame so that the section that looks smaller is pointing outward, while the side with the wider opening is pointing inward, to the interior of the house, and the side with the smaller opening is pointed outside.

The outside section of the frame is flat against the side of the house.

The inside section of the frame has a lip all around it to help hold in the window workings.

After this inner window frame is in place and the glue is dry, I started on the window workings.

First I cut a piece of clear plastic to fit the top section of the inside of the window. I glue it in place at the top of the frame. Then, using wood coffee stirrers, I made a little wooden frame for the whole inside of the window. It covers the edges of the top section of plastic glass and stretches all the way to the bottom of the window frame.

First section of plastic in place, with frame glued around it.

Next, I cut a piece of coffee stirrer to finish framing off the top half of the window.

Top half is framed off. Note that I have to trim the plastic at the bottom as it was made a bit too long. I will do that with an exacto once the glue is all dry.

Next, I cut a section of clear plastic to fit the bottom half of the window. I cut this so its frame will overlap the the bottom of the top frame. This will keep the bottom half of the window from falling out to the outside.

Lower window plastic is cut so it is tall enough that its frame will line up with the wood in the middle of the window.

Next, I made a little frame around this piece of glass out of the coffee stirrers. I make sure that it will fit inside the window ok.

Frame built around the lower half of the window.

I set this lower window frame in place at the bottom of the window.

Lower half of window, the part that will move up and down, set in place.

Finally, I made a frame around the edges of the window frame. This wood will hold the lower part of the window in place so it won’t fall out of the window on the inside. Make sure you don’t get any glue on the moving, lower section of window, as it won’t be able to open if it is glued to the trim.

Trim glued in place to keep lower half of window from falling out.

When it is done, you should be able to easily move the lower half of the window up and down. It won’t stay open on its own, but you could cut a small dowel to prop it open.

Once the inside of the house is complete, I will finish it off with a nice bit of decorative trim around the whole window. I plan on making a small framed piece of screen to use as a window prop to hold the window open in some rooms. You could also use a section of dowel if you want the widow to remain open. Mine will probably stay closed to keep curious paws out.

How to make an Old West Saloon Dollhouse out of a Duracraft Deluxe Victorian Mansion

Immediately after I brought it home.

This house was an unfinished kit that I bought on Facebook Marketplace. It still had the instruction manual, plus an old sales catalog from Frank’s Nursery dated 1982, with this kit circled. I am guessing that was when it was purchased, and it had never been finished. It has a lot of dust on it.

Something about this dollhouse makes me think of a large saloon and brothel in an old west town. We just finished watching the old ‘Deadwood’ series (HBO) and I can’t help envisioning Al sitting on the upper porch drinking his coffee. When I found this house available within easy driving distance, at an affordable price, especially in its unpainted state, I dove for it!

After the porch railings were finished. It looks more like a saloon to me now!

The first thing I did was finish the porch railings. The kit hadn’t been completed, and fortunately they included the instructions and the unfinished parts. It was easy to follow the instructions and install the porch rails.

Once the railing was installed, I turned the house around to focus on the inside. None of the inside walls had been installed, so the inside was a blank slate, which is great for me and my saloon intentions. However, without the support of the inside walls, the floors had sagged with time. I think someone probably used it like a shelf, which would have added to the problem. I decided that it needed some support, but I didn’t want any extra walls to break up that glorious open space on the bottom floor, so what to do?

I bought some fancy decorative wooden trim from Menards and glued it along the front edges of the floors, where it sagged the most. I clamped it until the glue was dry. I used pieces of wood to brace it up as it dried to it wouldn’t sag anymore. This would work temporarily, but I knew that it would be weak over time if it didn’t have some better support. Before I could add any extra support, however, I would need to get the floors done on the bottom floor.

I also cut one of the front windows bigger, making it into a door. I bought a swinging bat-wing door on Amazon and glued it in place, but there is a gap on the top that will need to be repaired.

The kit came with flooring strips (YAY) so I worked at cutting and gluing them down. I kept the lengths staggered so there is no pattern to the wood that would draw the eye, just like a real wood floor. The pieces were so thin that the wood glue I used made them curl up in some areas. I weighed them down with heavy glass cup holders until they were dry.

When the floor was laid, I cut some square wooden dowels to make a bracing framework across the middle of my floor. Eventually I can make some sort of fancy corbels or something to spruce it up, but I am confident that it will help to brace the floor above just as a wall would. In this picture you can see the trim I added above the doorway to cover the gap–it wasn’t quite tall enough, so I added a strip of leftover flooring above that. It seems to blend in the with the wood of the walls enough that it works.

Next I need a bar.

This was made with leftover fancy trim from what I used to brace the edge of the floor, plus jumbo craft sticks and square dowels. I used small round dowels, cut in half length-wise, for the round edges on the ends.

Bar in place, with a couple of dolls posing. I built some narrow shelves around the doorway to the back room, lining them with alcohol bottles I found on Amazon and Ebay. The mirror behind the shelves is from the back of a mirrored phone case I bought at dollar tree. The foot rest at the bottom of the bar is made of coffee stirrers (I shoved round toothpicks inside for support) and pieces of square dowel. I bought the spittoons on ebay.

This is where I’m at right now. I plan to get more dolls. I want some bored dancing girls, some patrons playing cards, rooms upstairs, and a storage room behind the bar. Stay tuned!

What my Haunted Beacon Hill Dollhouse Looks like on the Inside

This is my haunted/abandoned Beacon Hill dollhouse. Its main resident is Ash from the Evil Dead, who is visible on the front porch, enjoying a smoke and a beer with his zombie friend (hey, it’s make believe, darn it!)

This is my Beacon Hill, which has been featured in past posts. It is, of course, a work in progress, much like my other houses/structures. I work on different projects sporadically as my time, interests, and supplies allow. I thought today that you might enjoy seeing the insides and some of the modifications I have made to it. At the moment it is decorated for the winter, with snow on the roof. The snow, by the way, is just a fuzzy fleece sweatshirt that was cut into pieces and laid on the surfaces.

Ash (a Neca action figure from the Evil Dead series) with a glass of beer and cigarette that were purchased on ebay. His friend is a zombie that I am guessing could be from the Walking Dead but I really don’t know. Their metal lawn chairs were from Dollar General, in the Fairie Garden section.

So, for the life of me, I cannot get this image to upload in the correct orientation. It is tilted sideways for now until I can figure it out. Anyway, this is a full view of the back. I keep it covered (at least the bottom couple of floors) with a piece of plexiglass that is velcroed to the back of the house. It helps keep out dust and cats.

A closeup of the kitchen. I have a metal Roper range (and love it so much!), a Dee’s Delights wringer washer, a (I believe) Reuter’s kitchen sink, a wooden chopping block, and a Peripera makeup refrigerator. (I might paint that sometime so it looks more like a realistic vintage fridge. ) One of my ‘broken’ windows fell out and I didn’t catch it before taking the photo.

Dining room. I cut a small storage under the stairs. I still need to make a door for it. The front doors of the house still need to be re-attached, but for now they look fine as being caved in, as though it was broken into.

Here is the living room. I have a denim-covered couch that I love, a leg lamp (it is actually a night-light version of the famous Christmas Story lamp), and a few other pieces of furniture. The white chairs are my version of old fashioned table chairs. They aren’t finished yet.

Upstairs sitting room. It is occupied by my child’s toy kitties lol!

Bathroom. It is also occupied by pets. I used watered-down paints to dirty up the appliances a bit, and also the floor. I am still working at painting the trim brown. It was all white when I bought it, and, while it looked very nice, it just didn’t give me the ‘old house’ feel that dark wood has.

The back of the roof tower. It didn’t originally have a door, so I cut and added one. I might add a ghost in there eventually. I made the shingles out of jumbo crafting sticks, by cutting the rounded ends off and overlapping them.

This was originally decorated as a nursery, but I am converting it to a secret room. I made a shallow book case to block the entrance (will eventually add hinges to it), and then managed to find a vintage METAL spiral staircase kit on ebay! This is, perhaps, my favorite feature of this house, so far. I painted it black, and then used some brown paint to add a little ‘rust’. I used a rotary tool to cut the hole in the ceiling for the stair opening, and then patched around it with cloth and glue. i plan to paint over it when I eventually repaint the room, and make the loose cloth look like falling plaster.

The spiral staircase leads to a tiny greenhouse on the roof. I made the greenhouse out of a fancy metal cage that once held scented potpourri. I covered it with clear plastic that I salvaged from plastic food containers. The fence in front of it is a work in progress that I am still figuring out. Eventually I hope to make it encircle the rooftop.

The upstairs hallway. The ceiling needs to be patched where there was a gaping hole leading to the tower. Since I made the tower an actual room, I need to put a floor there for it. I bought the bookshelf on ebay, and now I need to stain it and add books and decorations.

Ash’s bedroom, top right room, with a skeleton friend.

Pennywise in the guest bedroom (middle floor, right side). Pennywise is a Neca figure. He has balloon dog christmas tree ornaments as props, and a giant praying mantis as a dinner guest. I like to position him in fun areas, like in the closet, peeking out a window, etc. Behind him is a small glass display case that I am currently pretending is a large fish tank, with ‘Safari’ brand deep sea fish in it.

This is the progress I have made on this house so far. There are still projects left to do before it is ‘done,’ but, in reality, I will probably always find more things to do with it. It would be fun to add artwork sometime, or black-and-white photos, and I would REALLY like to make a basement that I can set the whole house on top of, with a stairway that leads outside, like some of the really old houses have. Then I could make a boiler and laundry room, and make it damp-ish looking and creepy–an ideal place for Pennywise to hide. Hmm…

How to turn an Antique Dollhouse built from Crates in 1887 into an old Fashioned General Store

Side view. Panels on the side lift up on hinges, and have a wooden dowel that helps hold them up while you play.

As you can see, this window needs some restoration. I eventually used Museum Wax to stick the glass back under the thick paper frame.

My cat’s back is in this shot- don’t be alarmed, it’s just Teracles :).

Old wiring in the attic, that was modified by a recent owner with a more modern plug. Not sure how safe this would be to plug in, so I choose not to.

This is another marketplace find. The couple I bought this house from had found it in an antique shop many years ago. Apparently it was built in 1887, by a doctor, to give to his daughter. I confirmed with members of my antique dollhouse group on Facebook that this is probably authentic, as the glass is thick and imperfect, the wood looks to be from old-growth trees, and it was popular at that time to make houses out of crates. This house also appears to have been modified slightly through the generations, as someone added electricity via antique Christmas lighting.

It came furnished with a variety of Strombecker furniture, plus a pair of Erna Meyer dolls. I have decided to decorate the downstairs as a small general store (1800’s style), with the store keeper and his wife residing in the upper level.

When I was younger we had the opportunity to walk through a General Store that had been closed up, with all goods intact, for many decades. It was a magical moment to step into the past like that, and I would like to try to recreate that feeling (at least to a degree) in this dollhouse. The old store had a post office inside, goods on shelves and hanging from the ceiling, lots of old displays, and all sorts of stuff.

I don’t plan on altering the house itself in any way that can’t be undone. I have decided that any beams that I add for hanging goods will be held in place with museum wax so they can be easily removed.

I moved all of the ‘living’ furniture into the upper floors of the house, and any that didn’t quite fit in were stored in the dollhouse’s attic. Next step will be getting store furnishings, and making goods to sell!

I made this 2 sided store display out of craft sticks and split dowels.

First I made this 2 sided display out of craft sticks. I figured that it would work well in one of the windows as a display. I stained it and loaded the shelves with extra dollhouse items I had lying around.

Next, I found a cool post office display and bought it off ebay.

Post office display, along with packages and letters, on my messy desk (sorry!)

I also acquired a glass display counter and a few more goods for the store. Here is how it currently looks:

Display counter, post office, and window display all installed. There is also a cast iron stove and a grindstone pencil sharpener.

A closer view. The glass display domes were bought at Hobby Lobby and the cool, intricate scale was found on ebay. The cash register is a metal pencil sharpener.

Obviously there is much more work to be done. I would like to make some horse harness and tack to put on display, as well as removable beams across the ceiling to hang goods from, like candles and baskets. At some point, I would also like to figure out how to make antique-looking medicine bottles (I collect them in real life) that can be displayed on shelves or even in the glass display case. One of the fun things about doll houses is that you can always come up with fun ideas for future projects.

My Pepperwood Farm Dollhouse, Inside and out

This is the Pepperwood Farm dollhouse. I was fortunate enough to acquire it from Facebook marketplace in September of 2019. We drove across the state on a 3 hour, one-way drive to get it. These houses were made from plans that were sold in a book. It was built by hand with thick plywood, so it is very heavy!

I believe that this particular house was built in the late 1970’s-early 1980’s. The wallpapers are a bit brittle and faded from age (but I love them). The older couple who had inherited it from their friend decided to pass it on to another who would enjoy it just as much, so I was fortunate to come across it.

There isn’t much that I plan on changing with this house at the moment. The inside has been decorated wonderfully, with trims and papers that I adore, but could use a few finishing touches, along with some light restoration. Mostly I have been having fun with making and collecting furniture for it.

The windows open like real windows, the attic has studs in the storage room, the attic bedroom has a few built-ins. It’s such a quaint little home, and my daughter and I have fun playing in it together.

Here is an image of the space under the hinged roof. On the left is the untidy nursery, and on the right is the untidy attic. Note the studs in the walls, like an unfinished space. I love the details that the maker put into this house.

A closeup of the nursery. Note the built-in cupboards/drawers in the back. These appear to be made of thin wood.

This is the side with the front door and porch opened up. It has the stairwell, the bathroom, the main bedroom, and the parlor. This is during Christmas.

A closeup of the main bedroom, before I got the mattress made for the bed. The trunk was something I made as a teenager and the bedroom set was a vintage victorian bedroom kit from Realife Miniatures.

A closeup of the parlor. The parlor organ was a windup music box that I altered to resemble a Reed Organ, using wood, popsicle sticks, and dowels.

The stairs. The rug is a wide strip of ribbon, with stair rods made of toothpicks capped with beads, held in place with blue sticky putty (until I switch it to museum wax).

The bathroom. I found some glass mosaic tiles that I eventually plan to install. I think I will attach them to matboard and piece it in along the walls and floor so I can just cover up the existing stuff without damaging it. The doll is a Ficen, with a Tom Holland head added.

This view is with the other side opened up. It shows the kitchen, dining room, second bedroom, and upstairs hallway.

The second bedroom. I plan on making this the grandmother’s room. I would like to make a murphy bed to put in here. I did make the rolltop desk as a miniature of my own desk, and the trunk is one I made as a teenager. This is an older photo, as I now have a nicer Heidi Ott sewing machine.

The dining room, with my daughter’s toys in residence.

The kitchen. I made the piesafe out of popsicle sticks. I would like to make a decent hoosier cabinet to put in here, also. There is one that I made (out of view
on the wall opposite the sink) but I wasn’t very happy with it and want to replace it.

The insides of this house are constantly changing and evolving as I find different pieces of furniture or as I decorate for the seasons. Lately I have found myself wondering what new siding would look like, or even bricks? In my area of Michigan, I see a lot of old brick farmhouses, and they are breathtaking! I haven’t seen any photos of a brick pepperwood farm before. Perhaps someday I will try it out, even if it’s just printing some bricks on paper and taping them to the siding to see what it might look like.

Have any questions or comments? Want to see more photos of anything specific? Just leave a comment in the comment section!

How to Easily Make Broken Dollhouse Windows Without Breaking them

For my Beacon Hill project, I decided that, as the house is in disrepair, I wanted to add broken windows. However, as I really don’t enjoy breaking things, I decided to try something to make them LOOK broken.

I started out with a piece of clear plastic from a vegetable container from the store.

I am just showing this piece as an example. Obviously, it is much easier to use a piece that doesn’t have a large sticker on it!

After picking out your piece of clear plastic, cut it so that it can slide into the existing window, over top of the existing plastic or glass. I made mine just a hair larger so that it could be popped into place and hopefully stay put!

Cut to size

After the plastic is cut to the desired size, I used an xacto knife to carve cracks, holes, bullet holes, etc into them. Here are some examples:

Bullet holes. Notice that a lot of bullet-ridden glass has smaller spider-webs around the holes, as the bullet passes through with so much force.

After you have your broken windows prepared, gently insert them over your old windows, popping them into place. I placed my windows on the INSIDE of the house, so that they aren’t bumped as often, as they might fall out if jostled.

You can also keep some of the ‘shards’ left after making your holes, and drop them on the floor of your dollhouse, as broken glass.

You could leave slivers of broken glass around the edges of the pane, so it looks like a giant hole. You could make the whole window spider-webbed. The possibilities are endless!

How to Paint a Beacon Hill Dollhouse so it looks Abandoned or Haunted

So, during lockdown in 2020, I was lucky enough to find a reasonably priced Beacon Hill Victorian mansion for sale on marketplace. I purchased it, made some repairs, and decided to redecorate it as an aged house, fallen into disrepair.

This is my Beacon Hill on the day I purchased it. The porch had become detached and it really needed new paint on the exterior. A few minor pieces were missing but nothing I was concerned about, as I planned to make it a neglected house.

First things first, I needed to reattach the porch, which, luckily, was included with the house. I used wood glue and painstakingly pieced it all back together.

This photo shows the reattached porch, plus the beginning of the first layer of new paint.

Next step was a layer of light gray paint. I used some leftover house paint that I had laying around.

For the next step, I found some dark gray paint, and, using a stiff-bristled brush, I scrubbed this paint into the cracks and crevices to look like weathering and dirt. I scrubbed the brush up and down and side to side, wiping away excess paint, until i had achieved the look I wanted. I continued to do this over the whole exterior of the house.

After the dark gray was looking the way I wanted, the next step was to add a bit of dark green. I wanted it to be very faint, so i brushed it on with my stiff brush and then wiped it off. The trick to this was to make it not uniform. I tried to make it more pronounced in areas that I felt might have more water runoff, for instance, and on areas of the boards that might be more exposed to the sun. In real life I have a white house, and have had to clean my own siding, so I have observed this to an extent.

I still need to paint the base, but I haven’t decided how I want to make the base look, yet. I may go with a cinder block foundation, which would require a different look, so, for now, I chose to leave it.

I plan on changing the shingles to a fishscale look, so I didn’t touch them at this time. It does look fine with the shingles that are on it, but I really wanted the fishscales, and will add them at a later time.

How to Paint a Plastic Dollhouse to look Haunted

Plastic Victorian dollhouse from Goodwill.

For my first dollhouse project, I found this plastic dollhouse at the local Goodwill store. I like the Victorian style and thought it might make a nice haunted mansion for Halloween.

First off, I peeled off all of the stickers. Then I chose a paint that would work for a good base coat. I chose Rust-Oleum’s 2x ultra matte, in a dark gray. Their 2x paints are formatted to bond to plastics, as well as many other materials. I followed the instructions on the can.

Rust-Oleum’s 2x paints will bond with plastic and many other materials. I chose a nice dark gray.

I put on a good base coat.

First coat in progress. The matte paint will lose its gloss as it dries.

Next, after the paint has dried overnight, I dug into my acrylics. I chose a mixture of Cerulean blue and Mars Black for the shingles. I eventually switched to Payne’s Gray instead of the black. I used the black (or payne’s gray, which is a very dark gray) in a more watery mixture to paint in the cracks of the shingles. Then I used the cerulean blue on a drier brush to brush over the raised portions, in a way that left the dark areas in the cracks undisturbed. This layering made the shingles stand out more.

A mixture of Cerulean Blue and Payne’s Gray (and some black) was brushed on the shingles to bring out more of the texture.

Next, I took a mixture of Deep Magenta and Payne’s gray to work on the siding.

Deep Magenta and Payne’s Gray were used for the siding.

I brushed them on much like I did with the shingles, using a more watery brush for the payne’s gray on the siding first, to fill in the cracks, then going over it again with the magenta, using a drier brush so it wouldn’t reach into the cracks.

The siding is very dark, with hints of magenta, to give it a weathered appearance.

I added a little dark green to the bushes and a few of the shingles, to make it appear mossy. I also added a little cerulean blue to the flowers on the side of the house. Any colors you want will do, but to keep the appearance haunted-ish, I would recommend keeping the colors muted with dark gray or black.

I’m rather pleased with the results thus far. I will probably get some sort of clear coat to spray over the paint when I am finished with it, to protect against scratches. I will post more on this project as I go! Enjoy!

How to Transform an old Dollhouse to resemble a First Period Colonial Style House

I found this dollhouse on Marketplace for $20, and I just love the simple design! It reminds me so much of a 1700’s colonial, that I am going to decorate it for that era, as well as I can.

When I found this dollhouse on Markeplace for $20, I just had to have it! It reminds me of a 1700’s colonial (first period home), with its simple design and nice wood siding.

Wouldn’t this be awesome with a walk-in fireplace?

The inside needs some definite updating.

The first thing I did when I brought this huge, heavy dollhouse home was to scrape off the old shingles. They appear to have been made out of sandpaper, which seemed to have worked well enough, but they were in such poor, water-damaged shape that I felt I needed to wash my hands thoroughly after handling it.

This handy tool holds a razor blade that I can use for scraping paint and whatever.

Next, I used a handy-dandy paint scraper, and went to work scraping off some of the peeling paint from the floors, walls, and ceiling.

While scraping the paint off. I focused more on removing any peeling paint, as I plan to put a thin coat of plaster on the walls, with some thin wood supports in walls and ceiling, to give it a more primitive effect.

So far, I plan to apply a thin coat of plaster to give the walls a more uneven white texture, with thin pieces of wood applied to walls and ceilings to suggest supports that I can hang things like dried herbs and baskets from. Because of this, I was only interested in removing flaking paint (which there was a lot of).

Using methods similar to those used in the farmhouse, I applied jumbo craft sticks to mimic real wood floors. I cut the rounded tips off the sticks with poultry shears and then applied them with glue, weighting them down in places that wouldn’t quite stay put. I used an xacto knife to trim around doorways and walls.

Next, I decided to work on the upstairs floors. I want to go with a pine board effect, similar to my farmhouse, but I would like the floors to look more weathered and stained. I plan to score the wood lightly with an xacto knife, to add wood grain, and then lightly stain them before varnishing.

Update:

This is the updated roof! After removing the paper shingles that were in poor shape, I made slate-like shingles (described in another post) out of vinyl floor tiles.

Next, I painted the walls white, using a thick paint so it looked like a thin coat of plaster. I took wood from an old flowerbed border fence, so it would have some nice weathering to it, and used that to make some wooden support beams for the lower floor. I carefully opened up the area under the stairs, so I can use it as a storage closet (I will eventually make a door for it).

A current photo of the lower floor. I have been experimenting with different flooring in the main room, and at the moment have settled on a combination of small ceramic tiles and leftover pieces of linoleum. I have tiny candle bundles hanging from the wooden beams, as well as baskets and a lantern. The fireplace is a ceramic walk-in style that I found on ebay.